DM8168 Z3 RPS board boot log

From RidgeRun Developer Connection
Jump to: navigation, search
U-Boot 2010.06 (Jul 10 2013 - 08:53:37)
TI8168-GP rev 2.0

ARM clk: 987MHz
DDR clk: 675MHz

I2C: ready
DRAM: 1 GiB
NAND: HW ECC BCH8 Selected
256 MiB
Net: Detected MACID:50:56:63:47:6d:c8
Ethernet PHY: GENERIC (x001cc915) @ 0x01
DaVinci EMAC
Hit any key to stop autoboot: 0

Loading from NAND 256MiB 3,3V 8-bit, offset 0x280000
Image Name: "RR Compressed Linux Kernel"
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2339068 Bytes = 2.2 MiB
Load Address: 81e00000
Entry Point: 81e00000
Automatic boot of image at addr 0x82000000 ...
## Booting kernel from Legacy Image at 82000000 ...
Image Name: "RR Compressed Linux Kernel"
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2339068 Bytes = 2.2 MiB
Load Address: 81e00000
Entry Point: 81e00000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Linux version 2.6.37-ridgerun (dchaverri@pbarrantes-desktop) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #6 Mon Nov 18 17:48:17 CST 2013
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: dm8168z3
vram size = 84934656 at 0x0
reserved size = 84934656 at 0x0
FB: Reserving 84934656 bytes SDRAM for VRAM
Memory policy: ECC disabled, Data cache writeback
OMAP chip is TI8168 2.0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 152712
Kernel command line: console=ttyO2,115200n8 notifyk.vpssm3_sva=0xBF900000 root=/dev/nfs nfsroot=10.251.101.12:/home/dchaverri/devdirs/DUMMY/dm8168-z3_turrialba/fs/fs rw ip=dhcp mem=364M@0x80000000 mem=320M@0x9FC00000 vmalloc=512M vram=81M mtdparts=omap2-nand.0:2560k(UBOOT),4352k(KERNEL),38400k(FS)
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 364MB 239MB = 603MB total
Memory: 606532k/606532k available, 93884k reserved, 244736K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xd7000000 - 0xf8000000 ( 528 MB)
lowmem : 0xc0000000 - 0xd6c00000 ( 364 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.init : 0xc0008000 - 0xc003b000 ( 204 kB)
.text : 0xc003b000 - 0xc0470000 (4308 kB)
.data : 0xc0470000 - 0xc04ae180 ( 249 kB)
SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:407
IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
Total of 128 interrupts on 1 active controller
GPMC revision 6.0
Trying to install interrupt handler for IRQ400
Trying to install interrupt handler for IRQ401
Trying to install interrupt handler for IRQ402
Trying to install interrupt handler for IRQ403
Trying to install interrupt handler for IRQ404
Trying to install interrupt handler for IRQ405
Trying to install interrupt handler for IRQ406
Trying to install type control for IRQ407
Trying to set irq flags for IRQ407
OMAP clockevent source: GPTIMER1 at 27000000 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 986.31 BogoMIPS (lpj=4931584)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
omap_voltage_early_init: voltage driver support not added
regulator: core version 0.5
regulator: dummy:
NET: Registered protocol family 16
omap_voltage_domain_lookup: Voltage driver init not yet happened.Faulting!
omap_voltage_add_dev: VDD specified does not exist!
OMAP GPIO hardware version 0.1
OMAP GPIO hardware version 0.1
omap_mux_init: Add partition: #1: core, flags: 0
_omap_mux_get_by_name: Could not find signal i2c2_scl.i2c2_scl
_omap_mux_get_by_name: Could not find signal i2c2_sda.i2c2_sda
registered ti816x_gpio_vr device
registered ti816x_sr device
pm_dbg_init: only OMAP3 supported
registered ti81xx_vpss device
registered ti81xx_vidout device
registered ti81xx on-chip HDMI device
registered ti81xx_fb device
registered ti81xx_vin device
ti81xx_pcie: Invoking PCI BIOS...
ti81xx_pcie: Setting up Host Controller...
ti81xx_pcie: Register base mapped @0xd7038000
ti81xx_pcie: Starting PCI scan...
PCI: bus0: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
regulator: VFB: 858 <--> 1397 mV at 1103 mV
vgaarb: loaded
SCSI subsystem initialized
omap_i2c omap_i2c.1: bus 1 rev4.0 at 100 kHz
omap_i2c omap_i2c.2: bus 2 rev4.0 at 100 kHz
Advanced Linux Sound Architecture Driver Version 1.0.23.
Switching to clocksource gp timer
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
PMU: registered new PMU device of type 0
omap-iommu omap-iommu.0: ducati registered
omap-iommu omap-iommu.1: sys registered
highmem bounce pool size: 64 pages
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 706
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
omap_uart.0: ttyO0 at MMIO 0x48020000 (irq = 72) is a OMAP UART0
omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
console [ttyO2] enabled
brd: module loaded
loop: module loaded
ahci ahci.0: forcing PORTS_IMPL to 0x3
ahci ahci.0: AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl platform mode
ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc
scsi0 : ahci_platform
scsi1 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a150fff] port 0x100 irq 16
ata2: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a150fff] port 0x180 irq 16
omap2-nand driver initializing
ONFI flash detected
NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������)
3 cmdlinepart partitions found on MTD device omap2-nand.0
Creating 3 MTD partitions on "omap2-nand.0":
0x000000000000-0x000000280000 : "UBOOT"
0x000000280000-0x0000006c0000 : "KERNEL"
0x0000006c0000-0x000002c40000 : "FS"
davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
davinci_mdio davinci_mdio.0: detected phy mask fffffffc
davinci_mdio.0: probed
davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown
davinci_mdio davinci_mdio.0: phy[1]: device 0:01, driver unknown
mice: PS/2 mouse device common for all mice
omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 1)
notify_init : notify drivercreated for remote proc id 2 at physical Address 0xbf900000
asoc: tlv320aic3x-hifi <-> davinci-mcasp.2 mapping ok
asoc: HDMI-DAI-CODEC <-> hdmi-dai mapping ok
ALSA device list:
#0: TI81XX EVM
TCP cubic registered
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
omap_voltage_late_init: Voltage driver support not added
Power Management for TI81XX.
smartreflex smartreflex: Driver initialized
omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
davinci_mdio davinci_mdio.0: resetting idled controller
net eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, id=1cc915)
Sending DHCP requests .
PHY: 0:01 - Link is Up - 100/Full
., OK
IP-Config: Got DHCP answer from 10.251.101.1, my address is 10.251.101.251
IP-Config: Complete:
device=eth0, addr=10.251.101.251, mask=255.255.255.0, gw=10.251.101.1,
host=10.251.101.251, domain=cr.ridgerun.com, nis-domain=(none),
bootserver=10.251.101.1, rootserver=10.251.101.12, rootpath=
VFS: Mounted root (nfs filesystem) on device 0:14.
devtmpfs: mounted
Freeing init memory: 204K
starting pid 38, tty : '/etc/rcS'
Loading coprocessors modules...
Loading cmem from 0x96C00000 to 0x98000000
CMEMK module: built on Nov 18 2013 at 15:11:04
Reference Linux version 2.6.37
File /home/dchaverri/devdirs/DUMMY/dm8168-z3_turrialba/proprietary/ezsdk-5_05_02_00/ezsdk/component-sources/linuxutils_3_22_00_02/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c
CMEM Range Overlaps Kernel Physical - allowing overlap
CMEM phys_start (0x96c00000) overlaps kernel (0x80000000 -> 0xa5b00000)
allocated heap buffer 0xde000000 of size 0x1400000
heap fallback enabled - will try heap if pool buffer is not available
cmemk initialized
SysLink version : 2.20.02.20
SysLink module created on Date:Nov 18 2013 Time:15:11:18
FIRMWARE: Using default Memory map
FIRMWARE: isI2cInitRequiredOnM3: 0
FIRMWARE: Default memory configuration is used
Firmware Loader debugging not configured
Default FL_DEBUG: warning
Allowed FL_DEBUG levels: error, warning, info, debug, log
MemCfg: DCMM (Dynamically Configurable Memory Map) Version : 2.1.2.1
FIRMWARE: 1 start Successful
FIRMWARE: Using default Memory map
FIRMWARE: isI2cInitRequiredOnM3: 0
FIRMWARE: Default memory configuration is used
Firmware Loader debugging not configured
Default FL_DEBUG: warning
Allowed FL_DEBUG levels: error, warning, info, debug, log
MemCfg: DCMM (Dynamically Configurable Memory Map) Version : 2.1.2.1
FIRMWARE: 2 start Successful
FIRMWARE: Using default Memory map
FIRMWARE: isI2cInitRequiredOnM3: 0
FIRMWARE: Default memory configuration is used
Firmware Loader debugging not configured
Default FL_DEBUG: warning
Allowed FL_DEBUG levels: error, warning, info, debug, log
MemCfg: DCMM (Dynamically Configurable Memory Map) Version : 2.1.2.1
FIRMWARE: 0 start Successful
VPSS_FVID2: M3 firmware version 0x1000145 is newer,driver may not work properly.
HDMI W1 rev 2.0
HDMI CEC Spec version 1.2
I2C No Ack

Starting System
done.
Welcome to
__________ .__ .___ __________
\______ \|__| __| _/ ____ ____ \______ \ __ __ ____
| _/| | / __ | / ___\ _/ __ \ | _/| | \ / \
| | \| |/ /_/ | / /_/ >\ ___/ | | \| | /| | \
|____|_ /|__|\____ | \___ / \___ >|____|_ /|____/ |___| /
\/ \//_____/ \/ \/ \/

Embedded Linux Solutions

For further information see:
http://www.ridgerun.com
Build host: pbarrantes-desktop
Built by: dchaverri
Build date: Mon, 18 Nov 2013 17:48:41 -0600
Build tag: dm8168-z3
Configuring network interfaces
Starting D-Bus message bus system
Initializing Video Decoders

Please press Enter to activate this console.
starting pid 165, tty '/dev/ttyO2': '-/bin/sh'


BusyBox v1.20.2 (2013-11-18 14:29:04 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ #