Release Notes for latest evaluation SDK for OMAP-L138 Hawkboard Board
- Product Name: Evaluation SDK for OMAP-L138 Hawkboard Board.
- Version: 1.00.00.
- Date: 07/12/10.
- Download link: NOT AVAILABLE .
Copyright Notice ©
This document and the software described in it are furnished under license with RidgeRun, and as such, may be used or copied only in accordance with the terms of the license. The contents of this document are furnished for informational purposes only and are subject to change without notice. RidgeRun, assumes no responsibility or liability for any errors or inaccuracies that may exist in this document. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form, without the prior written consent of RidgeRun.
Please read the full license agreement for the RidgeRun Evaluation SDKs .
ARM is a registered trademark of ARM Limited. Linux is a registered trademark of Linus Torvalds in the United States and other countries and is used by RidgeRun under license. Instruments and TI are registered trademarks of Texas Instruments Incorporated. All other trademarks are the property of their respective owners.
|NOT AVAILABLE||Initial Version|
General SDK documentation:
- In some systems before to configure the SDK (make config) may be necessary to set bash as the default shell, this will be request by the system with the following message: bash is not your default shell, in this cases the following two commands must be entered:
$ sudo rm /bin/sh sudo ln -s /usr/bin/bash /bin/sh
- Now, in the configuration window go to File System Configuration->Select target's file system software and uncheck the package named gstd.
- In order to get an appropriate compilation of the SDK for OMAP-L138 Hawkboard, the following packages must be installed: libdbus-glib-1-dev and gperf.
$ sudo apt-get install libdbus-glib-1-dev gperf quilt
- Furthermore, If the system used to compile the SDK has a newer version of libtool than the version used by the SDK the compilation process will fail and and the following error will be shown:
libtool: Version mismatch error. This is libtool 2.2.6, but the libtool: definition of this LT_INIT comes from libtool 2.2.6b. libtool: You should recreate aclocal.m4 with macros from libtool 2.2.6 libtool: and run autoconf again
to fix this, the file local.tools (located in <yourSDKlocation>/OMAPL138SDK880207/bsp/oscheck) must be edited, the last line must be commented as is shown in the following example:
#mtd-tools:mtd-utils-git automake:automake-1.11 valac:vala-0.7.9 #libtool:libtool-2.2.6
Finally, go to the directory <yourSDKlocation>/OMAPL138SDK880207/proprietary/gst-dmai-plugins and run the following commands:
$make $autoreconf $quilt pop
Now, all should be ready to compile the SDK, then go to <yourSDKlocation>/OMAPL138SDK880207 and run:
OMAP-L138 Hawkboard Board Board related documentation:
- iUniversal iUniversal on the Hawkboardsudo rm /bin/sh
sudo ln -s /usr/bin/bash /bin/sh
- TI's software TI's available software for Hawkboard
- GStreamer Using Gstreamer on the Hawkboard
- Bootloader Configuration Configure u-boot environment for Hawkboard
- Recovering U-boot Getting u-boot prompt using UART port for Hawkboard.
- Hawkboard Community
- OMAP L138
Supported Operating Systems
- Ubuntu 10.04 in 32 bits.
- Ubuntu 9.04 in 32 bits.
- Ubuntu 9.10 in 32 bits.
Setting up extra components
- The first release is rigth now on a testing step
- Its coming soon
Integration with DSVDK
The DVSDK OMAP-L138_setuplinux_1_00_00_11.bin used can be find in
- Ti OMAP-L138 Low Power Application Processor
- 300-MHz ARM926EJ-STM RISC CPU
- 300-MHz C674x VLIW DSP
- On-Chip RTC
- 128 MByte DDR2 SDRAM running at 150MHz
- 128 MByte NAND FLASH
- 1 SD/MMC Slot
- One RS232 Serial Port
- One Fast Ethernet Port (10/100 Mbps)
- One USB Host port (USB 1.1)
- One USB OTG port (USB 2.0)
- One SATA Port (3Gbps)
- One VGA Port (15 pin D-SUB)
- Two AUDIO Ports (1 LINE IN & 1 LINE OUT)
- One Composite IN (RCA Jack)
- SPI (x2)
- I2C (x1)
- Linux BSP: PSP SDK 03.20.00.11
For details on the status of the basic drivers available on the RidgeRun SDK for Hawkboard, please visit Status of the hardware drivers on the Hawkboard page.